| Part |
Description |
| .100 breakaway header |
male breakaway headers |
| .100 breakaway header (right-angle) |
male breakaway headers (with a 90 degree bend) |
| .100 shunt |
shunt connecter aka motherboard jumpers |
| .156" 2 position housing |
a high power header connector |
| .156" 4 position housing |
a high power header connector |
| .156" crimp-on connector |
crimp on connectors for the high power connector |
| .156" header |
a high power header connector |
| 0.5 ohm 2 watt resistor |
2 watt resistor |
| 1 nF ceramic capacitor |
ceramic capacitor |
| 1 uF electrolytic capacitor |
electrolytic capacitor |
| 1.6K ohm resistor |
1/4 watt resistor |
| 1.8K ohm resistor |
1/4 watt resistor |
| 10 nF ceramic capacitor |
ceramic capacitor |
| 10 pin IDC connector |
a 2 row, 10 pin polarized IDC connector. |
| 10 pin IDC header |
a 2 row, 10 pin polarized IDC header. |
| 10 uF electrolytic capacitor |
electrolytic capacitor |
| 100 nF ceramic capacitor |
ceramic capacitor |
| 100 uF electrolytic capacitor |
electrolytic capacitor |
| 1000 uF electrolytic capacitor |
electrolytic capacitor |
| 100K ohm resistor |
1/4 watt resistor |
| 100K thermistor |
100K ohm glass bead type, beta = 4066 |
| 100nF ceramic capacitor 1206 |
a surface mount ceramic capacitor |
| 10K ohm resistor |
1/4 watt resistor |
| 10K thermistor |
10K ohm glass bead type, beta = 3480 |
| 10nF ceramic capacitor 1206 |
a surface mount ceramic capacitor |
| 12 pin .200" terminal block |
eurostyle terminal blocks |
| 12 pin header |
power connector |
| 12 pin housing |
connector housing |
| 14 pin DIP socket |
a socket to mount the chip in, just in case |
| 16 pin DIP socket |
a 16 pin socket to mount the RS232 chip in, just in case it gets fried. |
| 18 pin socket |
a DIP socket for mounting the microcontroller |
| 180 ohm resistor |
1/4 watt resistor |
| 1K ohm resistor |
1/4 watt resistor |
| 1M ohm resistor |
1/4 watt resistor |
| 1N4004 |
general purpose diode |
| 1N4005 |
general purpose diode |
| 1N4148 |
signal diode for various purposes |
| 1N5817 |
schottky diode for blocking signals |
| 1uF electrolytic capacitor D55 |
a surface mount electrolytic capacitor |
| 2 pin .200" connector |
eurostyle terminal blocks |
| 2 pin header |
signal connector |
| 2 pin housing |
connector housing |
| 2.7K ohm resistor |
1/4 watt resistor |
| 20 pin DIP socket |
a DIP socket for mounting chips |
| 220 ohm resistor |
1/4 watt resistor |
| 2200 uF electrolytic capacitor |
power regulation capactor. 25v or higher. |
| 22K ohm resistor |
1/4 watt resistor |
| 2K trimpot |
a 2K ohm trimpot |
| 3 pin header |
signal connector |
| 3 pin housing |
connector housing |
| 3.3 nF ceramic capacitor |
ceramic capacitor |
| 3.3K ohm resistor |
1/4 watt resistor |
| 330 ohm resistor |
1/4 watt resistor |
| 3mm green LED |
a small green led |
| 3mm red LED |
a small red led |
| 4 pin .200" terminal block |
eurostyle terminal blocks |
| 4 pin female header |
.100 male header plugs into this. |
| 4 pin header |
motor connector |
| 4 pin housing |
connector housing |
| 4 pin molex connector |
molex / disk drive style polarized power connector |
| 4.7K ohm resistor |
1/4 watt resistor |
| 4.7k ohm resistor 1206 |
a surface mount resistor |
| 4700 uF electrolytic capacitor |
power regulation capacitor. 25v or higher. |
| 5.6K ohm resistor |
1/4 watt resistor |
| 560 ohm resistor |
1/4 watt resistor |
| 560 ohm resistor 1206 |
a surface mount resistor |
| 5mm green LED |
a standard green led |
| 5mm red LED |
a standard red led |
| 6 pin IDC connector |
a 2 row, 6 pin, polarized IDC connector. |
| 6 pin IDC header |
a 2 row, 6 pin, polarized IDC header |
| 680 ohm resistor |
1/4 watt resistor |
| 74HC00N |
Quad NAND Gate |
| 78L05 |
a 5V voltage regulator |
| 9 pin DSUB |
9-pin female PCB-mounting D connector |
| AD595 |
thermocouple amplifier |
| AS5040 |
a surface mount magnetic rotary encoder chip |
| AS5040 |
a chip that provides magnetic rotary encoding (SMT) |
| Bicolor LED |
a two color LED that lights green for one polarity, and red for the opposite polarity |
| big heat sink |
heatsink for motor driver |
| crimp-on terminals |
crimp-on terminals for connections |
| Green LED 1206 |
a surface mount LED |
| H21LOI |
Optoswitch |
| HCPL2631 |
a chip that provides optical isolation |
| L293D |
a motor driver chip |
| L297 |
a motor controller chip |
| L298N |
a motor driver chip |
| MAX232 |
a chip to help communicate with the serial port |
| Omron B3F-1000 Button |
a simple pushbutton |
| PIC16F648A |
the microcontroller |
| SB360 |
a schottky diode 3A / 60V |
| small heat sink |
heatsink for power transistor |
| TIP110 |
darlington power transistor |
| TIP120 |
darlington power transistor |
| Type K Thermocouple |
a thermocouple |
| Part |
Description |
| Arduino |
this is an easy to program microcontroller board based around the atmega168 |
| Arduino Based Electronics |
These are the 2nd generation electronics |
| Arduino Breakout v1.0 |
a breakout board for the arduino for easier wiring - never released |
| Arduino Breakout v1.1 |
a breakout board for the arduino for easier wiring |
| Arduino Breakout v1.2 |
a breakout board for the arduino for easier wiring |
| Arduino Breakout v1.3 |
a breakout board for the arduino for easier wiring |
| Cartesian Robot v1.0 |
The 3D positioning system, ready to position. |
| DC Motor Driver v1.0 |
This board allows you to drive 2 small dc motors. |
| DC Motor Driver v1.1 |
This board allows you to drive 2 small dc motors. now with leds! |
| Extra Parts Kit |
Extra parts, in case you dont trust yourself. |
| Extruder Controller v1.2 |
The extruder controller, ready to control an extruder. |
| Magnetic Rotary Encoder v1.0 |
a magnetic rotary encoder board |
| McWire Cartesian Bot v1.2 |
this is a cartesian positioning system for printing |
| Opto Endstop v1.0 |
The opto endstop board, ready to provide endstops. |
| Opto Isolator v1.0 |
an optical isolator |
| PowerComms Board v1.2 |
The power/communications board, ready to provide power and communications. |
| PowerComms Board v1.3 |
The power/communications board, ready to provide power and communications. Now with blinkenlights. |
| Pulley Molds Kit |
Pulley molds, if you want to make your own pulleys. |
| PWM Driver v1.0 |
This board allows you to drive 3 channels of up to 5A each |
| PWM Driver v1.1 |
This board allows you to drive 3 channels of up to 5A each |
| RepRap v1.0 "Darwin" |
The entire RepRap machine, ready to print. |
| RepStrap v1.0 "Seedling" |
This is an easy to build repstrap machine to get you printing |
| Stepper Controller v1.2 |
The stepper controller, ready to control an axis. |
| Stepper Motor Driver v1.0 |
This board allows you to control one stepper motor |
| Stepper Motor Driver v1.1 |
This board allows you to control one stepper motor (with LED's now!) |
| Stepper Tester v1.0 |
The stepper tester, ready to test and blink. |
| Support Extruder v1.0 |
The support extruder, ready to extrude support material. |
| Temperature Sensor v1.0 |
this board does temperature monitoring |
| Temperature Sensor v1.1 |
this board does temperature monitoring |
| Thermocouple Sensor v1.0 |
an easy to use, high temperature sensor |
| Thermoplast Extruder v1.0 |
The thermoplastic extruder, ready to extrude. |
| Thermoplast Extruder v1.1 |
The thermoplastic extruder, ready to extrude. |
| Tools Kit |
Tools you will need to build a RepRap. |
| Universal Controller v1.2 |
The universal controller, ready to be specialized. |